Coperta1+2.cdr

Transcriere

1 Ancore pentru sarcini mici / Metalice wd HUS Sistem cu şurub universal (se va monta cu maşină de înşurubat cu impuls tangenţial TKI 2500) Date tehnice Extras din Manualul tehncii de ancorare Hilti Beton C20/25 Şurub universal HUS-/-S/-H/-A Cărămidă din var cu nisip Cărămidă cu goluri Beton poros G2/G4 Material de ancorare Forţă tracţiune rec.(zonă întinsă / comp.) [kn] 1,0 1,0 0,1 0,2 Forţă forfecare rec.v la dist.de margini³ 60mm [KN] 1,6 1,1 0,4 0,3 Forţă forfecare rec.v la dist.de margini ³ 30mm [KN] 0,5 0,4 0,2 0,1 Diametru gaură do [mm] Adâncime minimă de găurire h1 [mm] Adâncime minimă de montaj hnom [mm] Alte date tehnice puteţi găsi în Manualul tehnicii de ancorare Hilti, sau pe Internet la adresa HUS Şurub universal, x cap 10,2 mm, T40, x gaură 6 mm Înălţimi max. de fixare beton (recomand. Hilti) Cărămidă plină Cărămidă var cu nisip Cărămidă cu goluri beton poros Lungime şurub HUS 7,5x HUS 7,5x HUS 7,5x HUS 7,5x HUS 7,5x HUS 7,5x HUS 7,5x HUS 7,5x HUS 7,5x HUS 7,5x HUS 7,5x Capac de protecţie din material plastic pentru şurub universal HUS (T40) Culoare Execuţie alb suprapus HKO-T40 W maro deschis suprapus HKO-T40 HB maro închis suprapus HKO-T40 DB alb plat HKF-T40 W maro deschis plat HKF-T40 HB maro închis plat HKF-T40 DB HUS-S Şuruburi pentru ferestre x cap 7.7 mm, T 30, x gaură 6 mm Înălţimi max. de fixare beton (recomand. Hilti) Cărămidă plină Cărămidă var cu nisip Cărămidă cu goluri beton poros Lungime şurub HUS-S 7,5x HUS-S 7,5x HUS-S 7,5x HUS-S 7,5x HUS-S 7,5x HUS-S 7,5x HUS-S 7,5x HUS-S 7,5x HUS-S 7,5x Tehnica ancorării 157

2 Ancore pentru sarcini mici / Metalice Capac de protecţie din material plastic pentru şurub pentru ferestre HUS-S (T30) Culoare Execuţie alb plat HKF-T30 W maro deschis plat HKF-T30 DB HUS-H Ancoră şurub combinată cu cap hexagonal SW 13 şi T40, gaură x 6 mm Înălţimi max. de fixare beton (recomand. Hilti) Cărămidă plină Cărămidă var cu nisip Cărămidă cu goluri beton poros Lungime şurub HUS-H 7,5x HUS-H 7,5x HUS-H 7,5x HUS-H 7,5x HUS-H 7,5x HUS-H 7,5x HUS-A Ancoră şurub cu filet de racord, metric, gaură x 6mm Filet metric Lungime filet Lungime şurub M HUS-A 7,5x45 M 8/ M HUS-A 7,5x65 M 8/ M HUS-A 7,5x45 M 10/ M HUS-A 7,5x65 M 10/

3 Ancore pentru sarcini mici / Metalice wf HT Dibluri metalice pentru rame HT 8 L Execuţie: cu şurub cu cap semirotund plat Ø 9 mm. Utilizare: profile din material plastic şi aluminiu cu lăţimi ale canalului de îmbinare sub 11 mm. Cap şurub: Pozidriv mărime 2 Lungime diblu l x ext. mm = x nominal burghiu D de montaj h nom Cap şurub x HT 8 / 72 L HT 8 / 92 L HT 8 / 112 L HT 8 / 132 L HT 10 Execuţie: cu şurub cu cap înecat x 13 mm. Utilizare: pentru rame de ferestre şi căptuşeli de uşi. Cap şurub: Pozidriv mărime 3. Lungime diblu l x ext. mm = x nominal burghiu D de montaj h nom Cap şurub x HT10/ HT10/ HT10/ HT10/ HT10/ HT10/ HT10/ wg HAM Ancore pentru zidărie HAM Ancoră pentru zidărie cu filet interior NOU Tehnica ancorării x gaură D Adâncime gaură BT HAM M HAM M HAM M HAM M HAM Ancoră pentru zidărie, execuţie cu şurub, inclusiv calitate oţel 8.8 NOU x gaură D Adâncime gaură BT Grosime max. a materialului de fixat S max HAM M 6x HAM M 8x HAM M10x HAM M12x

4 Sarcini mici / Metalice wk HHD-S Dibluri pentru materiale cu cavităţi cu şurub premontat Material: nzidărie din cărămizi cu goluri Instrucţiuni de montaj: nplăci din ghips-carton nplanşee de camere, cu goluri Utilizare: nfixarea de şipci, şine, plăci, elemente decorative Material: nexecuţie complet din metal, zincat galvanic Is tfix Is tfix Date tehnice: HHD-S M4/20 M4/38 M5/38 M5/52 M6/38 M6/52 M 8/54 Nrec Gipscarton d = 9 (12,5) mm kn 0,2 (0,2) 0,2 ( ) 0,2 (0,2) 0,15 ( ) 0,2 (0,2) (0,2) Vrec Gipscarton d = 9 (12,5) mm kn 0,5 (0,5) 0,5 ( ) 0,5 (0,5) 0,4 ( ) 0,5 (0,5) (0,5) Nrec Placă din fibră dură = 4 mm kn 0,1 Vrec Placă din fibră dură = 4 mm kn 0,4 do Diametrul găurii mm h Grosimea mat. de fixare mm Is Lungimea şurubului mm tfix I Grosimea piesei fixate Lungimea diblului mm mm HHD-S Dibluri pentru materiale cu cavităţi cu şurub premontat Material: oţel zincat galvanic x gaură d 0 Lungime diblu l Lungime şurub l s x şurub d M4 4 HHD-S M4/ 4x M4 6 HHD-S M4/ 6x M4 12 HHD-S M4/12x M4 19 HHD-S M4/19x M5 8 HHD-S M5/ 8x M5 12 HHD-S M5/12x M5 25 HHD-S M5/25x M6 9 HHD-S M6/ 9x M6 12 HHD-S M6/12x M6 24 HHD-S M6/24x M6 40 HHD-S M6/40x M8 12 HHD-S M8/12x M8 24 HHD-S M8/24x M8 40 * grosimea materialului de ancorare la premontare Grosime material h + t max * HHD-S M8/40x execuţie cu cap hexagonal SW 13 Cleşte de montaj pentru HHD-S pentru montarea rapidă şi controlată a diblurilor Hilti pentru materiale cu cavităţi HHD-S Descriere Cleşte de montaj HHD-SZ HHD-SZ wl EFD Dibluri cu clapetă cu arc EFD-HM cu cârlig rotund x gaură 15 M 4 95 EFD-HM M EFD-HM EFD-RM cu tijă filetată şi inel x gaură 15 M 4 90 EFD-RM M EFD-RM Dimensiune filet mm Dimensiune filet mm Lungime totală cârlig (tijă) mm Lungime totală cârlig (tijă) mm

5 Sarcini mici / Metalice e0 MF-SKD Dibluri basculante Material: zincat Sarcină nominală recomandată per punct de fixare pentru ţevi la tablă tip trapez: 300 N Domeniu de sarcini: valori de sarcină conform prevederilor VdS, FM şi UL Adâncime minimă a golului (h) 90 mm x ştift filetat Lungime x nominal burghiu Lungime utilă ştift filetat după montaj M MF-SKD M 8/ M MF-SKD M 8/ M MF-SKD M 8/ M MF-SKD M 8/ M MF-SKD M10/ M MF-SKD M10/ ea DBZ Cuie tip pană DBZ 6/4,5 şi DBZ 6/35 Cuie tip pană Material: oţel, zincat galvanic 5 μm Înălţime max. fixare tfix[mm] x nominal burghiu d 0 Adâncime gaură h 1 Date tehnice cuie tip pană DBZ Material de ancorare beton C12/15 Extras din Manulul tehncii de ancorare Hilti DBZ 6/4,5 DBZ 6/35 Forţă tracţiune rec.(zonă întinsă şi comp. ) [kn] 0,8 0,8 Forţă forfecare recomandată V [kn] 1,1 1,1 Diametrul găurii do [mm] 6 6 Adâncime minimă gaură h1 [mm] Adâncime minimă de montare hnom [mm] Înălţimea maximă a fixării tfix [mm] 4,5 35 Lungimea diblului l [mm] Zonă întinsă: atunci când sunt disponibile mai mult de două puncte de fixare (suprapunere a încărcărilor).informaţii suplimentare puteţi găsi în Manualul tehnicii de ancorare Hilti, sau pe Internet la adresa Lungime diblu montare h nom 4, DBZ 6/4, DBZ 6/ es HA 8 Dibluri cu inel / Dibluri cu cârlig Date tehnice HA 8 Dibluri cu inel / Dibluri cu cârlig Material de ancorare beton M C16/20 Extras din Manualul tehnicii de ancorare Hilti HA 8 R1/H1 Forţă tracţiune rec.(zonă întinsă şi comp. ) [kn] 0,8 Diametrul găurii do [mm] 8 Adâncime minimă gaură h1 [mm] 50 Adâncime minimă de montare hnom [mm] 40 Porţiune liberă diblu / inel[mm] 26 Lungimea diblului l [mm] 66 Zonă întinsă: atunci când sunt disponibile mai mult de două puncte de fixare (suprapunere a încărcărilor). Informaţii suplimentare puteţi găsi în Manualul tehnicii de ancorare Hilti, sau pe Internet la adresa Tehnica ancorării HA 8 Dibluri cu inel Material: oţel, zincat galvanic 5 μm x nominal burghiu d0 gaură h diblu cu cârlig închis de ancorare h nom bax HA 8 R ) HA 8 H ) diblu cu cârlig deschis 161

6 Sarcini mici / material plastic ed HRD-U Dibluri universale pentru rame hnom Date tehnice extras din Manualul tehnicii de ancorare Hilti HRD Dibluri pentru rame HRD-S10 HRD-U10 HRD-U14 Diametru gaură şi diblu d0 [mm] Adâncime minimă de găurire h1 [mm] Adâncime minimă de ancorare hnom [mm] Grosime min. material de ancorare hmin [mm] Material de ancorare beton C20/25 Solicitare la tracţiune recomandată N [kn] 1,4 1,8 2,3 Forţă de forfecare recomandată V [kn] 1,8 2,0 2,5 Distanţă necesară faţă de margini Ccr [cm] Distanţă necesară între axe Scr [cm] Material de ancorare zidărie cu cărămidă plină Solicitare la tracţiune recomandată N [kn] 0,6 0,8 1,2 Forţă de forfecare recomandată V [kn] 0,8 1,0 1,3 Distanţă necesară faţă de margini Ccr [cm] Distanţă necesară între axe Scr [cm] Material de ancorare cărămidă cu goluri Solicitare la tracţiune recomandată N [kn] 0,25 0,25 0,3 Forţă de forfecare recomandată V [kn] 0,25 0,25 0,3 Distanţă necesară faţă de margini Ccr [cm] Distanţă necesară între axe Scr [cm] Informaţii suplimentare puteţi găsi în Manualul tehnicii de ancorare Hilti, sau pe Internet la adresa HRD-UGT Dibluri pentru rame x 10 mm Execuţie: cu şurub cu cap înecat pentru vârf torx T40, Material: oţel, zincat galvanic 5 μm Înălţime max. de fixare t fix x nominal burghiu d 0 Lungime. diblu l d Adâncime montare h nom HRD-URT Dibluri pentru rame x 10 mm Execuţie: cu şurub cu cap înecat pentru vârf torx T40 Material: oţel inoxidabil A4-70 (cod material Înălţime max. de fixare t fix x nominal burghiu d 0 Lungime. diblu l d montare h nom Adâncime gaură h 1 Adâncime gaură h HRD-UGT 10x 80/ HRD-UGT 10x100/ HRD-UGT 10x120/ HRD-UGT 10x140/ HRD-UGT 10x160/ HRD-UGT 10x180/ HRD-UGT 10x200/ HRD-UGT 10x230/ HRD-UGT 10x250/ HRD-UGT 10x290/ HRD-UGT 10x330/ Capac de protecţie din material plastic pentru HRD-UGT (T40) Culoare Execuţie alb suprapus HKO-T40 W maro deschis suprapus HKO-T40 HB maro închis suprapus HKO-T40 DB alb plat HKF-T40 W maro deschis plat HKF-T40 HB maro închis plat HKF-T40 DB HRD-URT 10x80/10* HRD-URT 10x120/ * aceste dimensiuni nu sunt premontate. HRD-UGS Dibluri pentru rame x 10 mm Execuţie: cu şurub cu cap hexagonal SW 13 Material: oţel, zincat galvanic 5 μm Înălţime max. de fixare t fix HRD-UGS 10x 80/ 10* HRD-UGS 10x100/ HRD-UGS 10x120/ HRD-UGS 10x140/ HRD-UGS 10x160/ HRD-UGS 10x180/ HRD-UGS 10x200/ HRD-UGS 10x230/ HRD-UGS 10x250/ HRD-UGS 10x290/ HRD-UGS 10x330/ * aceste dimensiuni nu sunt premontate. 162 x nominal burghiu d 0 Lungime. diblu l d montare h nom Adâncime gaură h 1

7 Sarcini mici / material plastic HRD-UGS/U Dibluri pentru rame x 10 mm Execuţie: cu şurub cu cap hexagonal cu guler mare şi şaibă suport integrată x 18 mm Cap: hexagonal SW 13 precum şi torx T40 Material: oţel, zincat galvanic 5 μm Înălţime max. de fixare t fix HRD-UGS 10x 80/10 U HRD-UGS 10x100/30 U HRD-SGS/U Dibluri pentru rame x 10 mm (adâncime de montaj 50 mm) Execuţie: cu şurub cu cap hexagonal cu guler mare şi şaibă suport integrată Ø 18 mm Cap: hexagonal SW 13 precum şi torx T40 Material: oţel, zincat galvanic 5 μm Înălţime max. de fixare t fix HRD-SGS 10x 60/10 U HRD-SGS 10x 80/30 U HRD-URS Dibluri pentru rame x 10 mm Execuţie: cu şurub cu cap hexagonal SW 13 Material: oţel, inoxidabil A4-70 (indice material Înălţime max. de fixare t fix x nominal burghiu d 0 Lungime. diblu l d montare h nom Adâncime gaură h HRD-URS 10x 80/ HRD-URS 10x100/ HRD-URS 10x120/ HRD-URS 10x140/ HRD-URS/U Dibluri pentru rame x 10 mm Execuţie: cu şurub cu cap hexagonal cu guler mare şi şaibă suport integrată x 18 mm Cap: hexagonal SW 13 precum şi torx T40 Material: oţel, inoxidabil A4 (indice material Înălţime max. de fixare t fix x nominal burghiu d 0 x nominal burghiu d 0 x nominal burghiu d 0 Lungime. diblu l d Lungime. diblu l d Lungime. diblu l d montare h nom montare h nom montare h nom Adâncime gaură h 1 Adâncime gaură h 1 Adâncime gaură h HRD-URS 10x 80/10 U HRD-URS 10x100/30 U HRD-SRS/U Dibluri pentru rame x 10 mm (adâncime de montaj 50 mm) Execuţie: cu şurub cu cap hexagonal cu guler mare şi şaibă suport integrată x 18 mm Cap: hexagonal SW 13 precum şi torx T40 Material: oţel, inoxidabil A4 (indice material Înălţime max. de fixare t fix HRD-SRS 10x60/10 U HRD-SRS 10x80/30 U HRD-UGT Dibluri pentru rame x 14 mm Execuţie: cu şurub cu cap înecat pentru vârf torx T50 Material: oţel zincat galvanic 5 μm Înălţime max. de fixare t fix x nominal burghiu d 0 x nominal burghiu d 0 Lungime. diblu l d Lungime. diblu l d montare h nom montare h nom Adâncime gaură h 1 Adâncime gaură h HRD-UGT 14x 80/ HRD-UGT 14x110/ HRD-UGT 14x140/ HRD-UGT 14x160/ HRD-UGT 14x180/ HRD-UGT 14x200/ HRD-UGT 14x230/ HRD-UGT 14x270/ HRD-UGT 14x310/ HRD-UGT 14x350/ Tehnica ancorării HRD-UGS Dibluri pentru rame x 14 mm Execuţie: cu şurub cu cap hexagonal SW 17 şi şaibă suport integrată Material: oţel zincat galvanic 5 μm Înălţime max. de fixare t fix x nominal burghiu d 0 Lungime. diblu l d montare h nom Adâncime gaură h HRD-UGS 14x 80/10U HRD-UGS 14x110/40U HRD-UGS 14x140/70U HRD-UGS 14x160/90U HRD-UGS 14x180/110U HRD-UGS 14x200/130U HRD-UGS 14x230/160U HRD-UGS 14x270/200U HRD-UGS 14x310/240U HRD-UGS 14x350/280U

8 Sarcini mici / material plastic ef HUD-L / FDL Dibluri pentru zidărie, lungi Materiale de fixare: nzidărie din cărămizi cu goluri nzidărie din cărămizi pline nbeton nplăci din ghips-carton nbeton poros, cărămizi din var cu nisip, pline şi cu goluri Material: nmaterial de nylon de mare calitate. Rezistent la temperaturi de la -40 C până la +80 C. Fără halogen pentru DIN-VDE 0472, partea 815. fără silicon şi metale grele (fără cadmium, plumb) x do h1 L 5 S L + S Date tehnice HUD-L 6 HUD-L 8 HUD-L 10 FDL 12 Nrec Beton C25/30 kn 0,90 1,30 1,80 Nrec Cărămidă cu goluri HLz M 12 kn 0,15 0,20 0,30 0,30 Nrec Plăci de ghips 2x12,5 mm kn 0,10 0,15 0,12 Nrec Beton celular autoclavizat G2 kn 0,12 0,25 0,40 Nrec Beton celular autoclavizat G4 kn 0,24 0,50 0,70 HUD-L / FDL Dibluri pentru zidărie, lungi x ext = x gaură d 0 gaură h 1 Lungime diblu l = adâncime ancorare h nom x şurub pt. lemn d ,5 5 HUD-L 6x HUD-L 8x HUD-L 10x FDL Dibluri pentru zidărie, lungi x ext = x gaură d 0 gaură h 1 Lungime diblu l = adâncime ancorare h nom x şurub pt. lemn d FDL12x eg HUD-1 Dibluri universale Materiale de fixare: nzidărie din cărămizi cu goluri cu strat de tencuială de până la 30 mm nzidărie din cărămizi pline cu strat de tencuială de până la 30 mm cu strat de tencuială de până la 30 mm nbeton poros, cărămizi din var cu nisip, pline şi cu goluri h1 l t fix Material: nmaterial de nylon de mare calitate. nrezistent la temperaturi de la -40 C până la +80 C. Fără halogen pentru DIN- VDE 0472, partea 815. fără silicon şi metale grele (fără cadmium, plumb) Date tehnice HUD-1 5 HUD-1 6 HUD-1 8 HUD-1 10 HUD-1 12 HUD-1 14 Nrec Beton C25/30 kn 0,3 0,55 0,85 1,4 2,0 3,0 Nrec Cărămidă cu goluri HLz M 12 kn 0,08 0,1 0,2 0,25 0,28 0,32 Nrec Plăci de ghips 12,5 mm kn 0,04 0,05 0,06 do Diametru gaură mm h1 Adâncime minimă de găurire mm d Diametru şurub mm 3,5 4 4, l Lungime diblu mm HUD-1 Diblu universal x ext = x gaură d 0 gaură h 1 Lungime diblu l = adâncime ancorare h nom x şurub pt. lemn d ,5 4 HUD-1 5x ,5 5 HUD-1 6x HUD-1 8x HUD-1 10x HUD-1 12x HUD-1 14x Cutie plastic cu 9 compartimente, goală Cutie dibluri HUD-1 Dibluri universale mare x ext = x gaură d 0 gaură h 1 Lungime diblu l = adâncime ancorare h nom x şurub pt. lemn d ,5 4 HUD-1 5x ,5 5 HUD-1 6x HUD-1 8x HUD-1 10x

9 Sarcini mici / material plastic eh Dibluri bătute l l Beton / Zidărie din cărămizi pline d0 d0 h1 hnom tfix hnom h1 tfix Zidărie din cărămizi cu goluri Dibluri bătute Execuţie: cu şurub cu filet conic, premontat, Material şurub cu filet conic: oţel, zincat galvanic Beton/Cărămidă plină Zidărie cărămizi cu goluri Înălţime max. fixare t fix Adâncime Înălţime max. montaj h nom fixare t fix Adâncime montaj h nom x nominal burghiu d 0 Adâncime gaură h 1 Lungime. diblu 0 până la / 0x până la / 5x până la / 10x până la / 15x până la / 30x până la / 0x până la / 5x până la / 10x până la / 15x până la / 25x până la / 30x până la / 40x până la / 0x până la / 10x până la / 30x până la / 40x până la / 60x până la / 80x până la /100x ej HLD Dibluri pentru gips-carton Date tehnice HLD 2 HLD 3 HLD 4 Nrec Plăci de ghips n M 12 mm kn 0,08 0,08 0,08 do Diametru gaură mm h Grosime material mm ls Lungime şurub mm 33 + tfix 40 + tfix 49 + tfix d Diametru şurub mm 4 4,5 4 4,5 4 4,5 l Lungime diblu mm Tehnica ancorării HLD Dibluri uşoare Pentru grosime material la tip de montaj* A x nominal burghiu d 0 x şurub d s Lungime şurub l s (9) 4, t fix HLD (9) 4, t fix HLD (9) 4, t fix HLD * tip montaj: A utilizare ca dibluri cu clapetă cu arc, B ca diblu de strângere 165

10 HGN gas concrete anchor Features: Material: - base material: lightweight concrete, gypsum panel, aerated concrete and other lightweight building materials - through-fastening possible - universal in application - good keying thanks to large fins - PA 6 polyamide, containing no heavy metals - containing no cadmium or lead - free of halogens and silicones - in-place temperature range: from 40 C to +80 C - temperature when setting: from 10 C to +40 C HGN Basic loading data (for a single-anchor fastening): HGN All data on this page applies to different kinds of base material no edge distance and spacing influence Mean ultimate resistance, R u,m [kn]: Anchor size HGN HGN HGN Base material 10x NRu,m PB 2 (G 2) VRu,m NRu,m PB 4 (G4) VRu,m NRu,m PB 6 (G6) VRu,m NRu,m P 3.3 (GB 3.3) VRu,m NRu,m P 4.4 (GB 4.4) VRu,m NRu,m Gypsum panel VRu,m NRu,m Pumice concrete VRu,m The compressive strengths of the base materials used to determine the data were as follows: PB 2 = 2.5 N/mm 2, 0.3 kg/dm 3 PB 4 = 5.0 N/mm 2, 0.5 kg/dm 3 PB 6 = 7.5 N/mm 2, 0.6 kg/dm 3 P 3.3 = 3.5 N/mm 2, 0.5 kg/dm 3 P 4.4 = 5.0 N/mm 2, 0.6 kg/dm 3 gypsum = 7.8 N/mm 2 pumice concrete = 4.7 N/mm Issue 2005

11 HGN gas concrete anchor Design resistance, R d [kn]: Anchor size HGN HGN HGN Base material 10x NRd PB 2 (G 2) VRd NRd PB 4 (G4) VRd NRd PB 6 (G6) VRd NRd P 3.3 (GB 3.3) VRd NRd P 4.4 (GB 4.4) VRd NRd gypsum panel VRd NRd pumice concrete VRd Recommended load, L rec [kn]: Anchor size HGN HGN HGN Base material 10x NRec PB 2 (G 2) VRec NRec PB 4 (G4) VRec NRec PB 6 (G6) VRec NRec P 3.3 (GB 3.3) VRec NRec P 4.4 (GB 4.4) VRec NRec gypsum panel VRec NRec pumice concrete VRec If there is a sustained tensile load at temperatures above 40 C, the recommended load should be reduced. Issue

12 HGN gas concrete anchor Setting details do d l=hnom h1 tfix Setting details Anchor size HGN 10x100 HGN 12 HGN 14* d0 [mm] Drill bit and anchor diameter h1 [mm] Min. hole depth l [mm] Anchor length ls [mm] Required length l + tfix + 5 l + tfix + 5 l + tfix + 5 d [mm] Required shank diameter 7 (6-8) (12) Drill bit TE-CX-10/17, TE-CX-10/22 TE-CX-12/22 TE-CX-14/22 * Recommendation: HGN 14 with 12 mm diameter PB 4 (G4), PB 6 (G 6): Hole of 15mm diameter. Installation equipment Rotary hammer (TE1, TE 2, TE5, TE6, TE6A, TE15, TE15-C, TE18-M), hammer, drill bit (See table above.) and a driver (SF 100, SF 120, SD45, SU25). Setting operations Drill hole with drill bit. Blow out dust and fragments. Install / tap in anchor Part fastened Drive into anchor. 132 Issue 2005

13 HLC sleeve anchor Features: - for concrete and solid masonry - force-controlled expansion - no rotation in hole when tightening bolt - reliable pull-down of part fastened HLC Material: HLC: - grade steel galvanised to min. 5 microns Concrete Fire resistance Basic loading data (for a single anchor): HLC, HLC-H, HLC-F, HLC-T, HLC-E All data on this page applies to concrete, f cc 20 N/mm 2 non-cracked concrete no edge distance and spacing influence 2 non-cracked concrete Characteristic resistance, R k [kn]: Anchor size M5 M6 M8 M10 M12 M16 Base material NRk concrete, fcc 20 N/mm 2 VRk Design resistance, R d [kn]: Anchor size M5 M6 M8 M10 M12 M16 Base material NRd concrete, fcc 20 N/mm 2 VRd Recommended load, L rec [kn]: Anchor size M5 M6 M8 M10 M12 M16 Base material NRec concrete, fcc 20 N/mm 2 VRec The recommended resistance (N rec and V rec ) for HLC-E is 0.5 kn. Note: To apply the right tightening torque (setting operations see following page) to the HLC-F, we recommend a hexagon socket wrench and for the HLC-T as well as HLC-E a driver. Issue

14 HLC sleeve anchor Setting details l lc do dh T inst hnom h1 h tfix Setting details Anchor size 6.5x25/5 6.5x40/20 6.5x60/40 8x40/12 8x55/27 8x70/42 8x85/57 10x40/8 10x50/18 10x60/28 10x80/48 10x100/68 12x55/17 12x75/37 12x100/62 16x60/12 16x100/52 16x140/92 20x80/25 20x115/60 20x150/95 d [mm] Thread diameter M5 M6 M8 M10 M12 M16 d0 [mm] Drill bit diameter ¼ h1 [mm] Min. hole depth hnom [mm] Anchorage depth [mm] Fixture (fastenable) tfix thickness l [mm] Anchor length lc [mm] Length under washer Tinst [Nm] Tightening torque Width across HLC 15 Sw [mm] nut flats HLC-H 17 dh [mm] Clearance hole h Drill bit [mm] Min. base material thickness TE-CX- ¼ /6 TE-CX-8/17 TE-CX-10/17 TE-CX- 12/17 TE-CX- 16/17 TE-C- 20/22S Installation equipment Rotary hammer (TE1, TE 2, TE5, TE6, TE6A, TE15, TE15-C, TE18-M or TE35), a drill bit (see table above), a hammer and a torque wrench. Setting operations Drill hole with drill bit. Blow out dust and fragments. Install the anchor. Apply torque. 104 Issue 2005

15 Anchoring Systems HLD Kwik-Tog PRODUCT DESCRIPTION The Hilti Kwik-Tog is a plastic anchor designed to accept No. 8 or No. 10 s for light duty applications in hollow or solid base materials Product Features Unique one piece design for easy setting Three convenient sizes for use in a variety of hollow base materials from 1/4 drywall to block and concrete Leg braces provide added support Ribs on body help prevent anchor from spinning during installation Remains mounted in the wall without for convenient handling, installation and reuse MATERIAL SPECIFICATIONS Plastic; polypropylene for use in temperature range from -40 F to +140 F TECHNICAL DATA Specification Table HLD Kwik-Tog TM 3 is specially designed for ⁵ ₈" sheetrock S = Thickness of material being fastened 5/18" - 3 /4" 3/4" - 7 /8" greater than 1 5 /8" 3/8" 3/8" 3/8" L d 1 1 /2" + S #8 or /2" + S #8 or /16" + S #10 or 12 HLD Kwik-Tog TM 2 is specially designed for 1 /2" sheetrock HLD Kwik-Tog TM 4 5/32" - 1 /2" 17/32" - 19 /32" greater than 1 3 /8"" 15/16" /8" 1 1 /8" /4" greater than 2" 3/8" 3/8" 3/8" 3/8" 3/8" 11/32" L d 1 1 /4" + S #8 or /4" + S #8 or /16" + S #10 or 12 L d 1 7 /8" + S #8 or /8" + S #8 or /16" + S #10 or INSTALLATION INSTRUCTIONS 1. Compress wings together. 2. Insert anchor through drilled hole. 3. Insert and tighten through fixture to expand wings. HLD Kwik-Tog Allowable Loads 1 1/2" Drywall 5/8" Drywall Hollow Concrete Tension Tension Block, Tension Description lb (N) lb (N) lb (N) HLD 2 20 (89) 25 (11 40 (178) HLD 3 35 (156) 50 (222) HLD 4 70 (31 1. Based on using a safety factor of ORDERING INFORMATION HLD Kwik-Tog Anchor Program Bit Hollow Base Allowable Recommended Screw Size* Item Diameter Material Load in 5 /8" Drywall Hollow Solid Quantity Description Number in. Thickness Tension, lb (kn) Base Mtl. Base Mtl. Per Box Kwik-Tog 2 (HLD2) /8 3/16" - 5 /8" 25 (0.1 #8 or #10 # Kwik-Tog 3 (HLD3) /8 5/8" - 7 /8" 35 (0.16) #8 or #10 #10 50 Kwik-Tog 4 (HLD4) /8 15/16" /4" #8 or #10 #10 50 * Screw not included 138 Hilti Product Technical Guide 10/99

16 HLD light-duty anchor Features: Material: - base material: virtually all existing building materials, especially panels and similar - universal/versatile in thin-walled and solid base materials, even if they are of low strength - bridges a large range of wall/panel thickness - safe against rotation in hole - excellent guidance - simple setting - setting check through noticeable increase in resistance when the has been driven home - polyamide PA 6, containing no heavy metals - without cadmium and lead - free of halogens and silicones - in-place temperature range: from 40 C to +80 C - temperature when setting: from 10 C to +40 C HLD Basic loading data (for a single anchor): HLD All data on this page applies to concrete: f cc = 15 N/mm 2 different kinds of base material no edge distance and spacing influence table values are for tensile and shear load Characteristic resistance, R k [kn]: Base Material Design resistance, R d [kn]: Base Material 125 Anchor working Size of anchor principle HLD 2 HLD 3 HLD 4 Concrete: fcc = 15 N/mm 2 C Gypsum panel B Fibre reinforced gypsum panel 12.5mm Fibre reinforced gypsum panel 2x12.5mm A A Asbestos cement A Hollow brick, fired A/B Sand-lime solid block KS DF Anchor working Size of anchor Principle HLD 2 HLD 3 HLD 4 Concrete: fcc = 15 N/mm 2 C Gypsum panel B Fibre reinforced gypsum panel 12.5mm Fibre reinforced gypsum panel 2x12.5mm A A Asbestos cement A Hollow brick, fired A/B Sand-lime solid block KS DF C Woodwool panel A See setting details page 97. C Woodwool panel A

17 HLD light-duty anchor Recommended load, L rec [kn]: Base Material Anchor working Size of anchor principle HLD 2 HLD 3 HLD 4 Concrete: fcc = 15 N/mm 2 C Gypsum panel B Fibre reinforced gypsum panel 12.5mm Fibre reinforced gypsum panel 2x12.5mm A B Asbestos cement A Hollow brick, fired A/B Sand-lime solid block KS DF C Woodwool panel A At temperatures above 40 C, the recommended load should be reduced for sustained tensile loading. Setting details 2 A B C h1 do do h tfix tfix ls tfix Setting details d0 Anchor size HLD 2 HLD 3 HLD 4 HLD 2 HLD 3 HLD 4 HLD 2 HLD 3 HLD 4 [mm] Drill bit diameter h1 [mm] Hole depth ls [mm] Screw length 33 + tfix 40 + tfix 49 + tfix 33 + tfix 40 + tfix 49 + tfix 40 + tfix 46 + tfix 56 + tfix d [mm] Screw diameter h [mm] Wall/panel thickness from 35 from 42 from 50 Drill bit TE-CX-10/17, TE-CX-9/22 TE-CX-9/22 Anchor working principle A B C Use a 9 mm twist drill for gypsum panel and woodwool panels, but a 10 mm drill bit for concrete. Installation equipment Rotary hammer (TE1, TE 2; TE5, TE6, TE6A, TE15, TE15-C, TE18-M) and a driver (SF100, SF120, SD45, SU25). Setting operations Drill hole with drill bit. Install the HLD anchor. Drive in the. 126

18 Anchoring Systems Impact Anchor PRODUCT DESCRIPTION The Impact Anchor consists of a carbon or stainless steel drive- and a plastic expansion body, which combine to form an easy to install but removable fastening for light duty applications in concrete and masonry. Product Features Philips drive connection is recessed in the head providing protection during hammering, allowing simple setting and removal Anchor collar and head form a compact unit which allows for countersinking in soft wood and solid clamping action with metal parts Expanding head opens in hollow base material to provide reliable keying effect One type anchor reduces inventory, providing versatile use in brick, hollow block and concrete Can be set with hammer or driver for quick and easy installation Available with 304 Stainless Steel Nail for corrosive environments Plastic body is temperature resistant from -40F to +176F. Anchor can be installed from +14F to +104F. Both features allow for use in extreme climactic conditions Suitable for through-hole fastenings to improve productivity Removability adds to the anchors versatility MATERIAL SPECIFICATIONS Corrosion resistant body made of polyamide 6.6 plastic Carbon steel drive material meets the requirements of AISI 1010 Carbon steel drive zinc plated to minimum 5 µm thickness in accordance with ASTM B633, Sc. 1, Type II Stainless steel drive material meets the requirements of AISI TECHNICAL DATA Allowable Loads * Base Material Anchor 3/16-1 3/ /2 1/4-1 1/4-1 5 /8 1/4-2 1 /16 1/4-2 5 /8 5/ /8 5/ /2 5/ /8 5/ /8 Concrete 2000 psi (13.8 MPa) Brick Masonry Hollow Concrete Block (Normal Wt.) Rec. Min. Embed. Depth Concrete Hollow Base Tension lb (N) Shear lb (N) Tension lb (N) Shear lb (N) Tension lb (N) Shear lb (N) in. in. 30 (133) 95 (422) 35 (155) 105 (467) 50 (222) 120 (534) 3/4 (19) 5/8 (16) 55 (245) 130 (578) 40 (178) 145 (645) 55 (245) 140 (623) 7/8 (22) 13/16 (2 70 ( (600) 45 (200) 165 (734) 60 (600) 160 (712) 1 (25) 13/16 (2 80 (356) 215 (956) 45 (200) 220 (979) 65 (289) 185 (823) 1 3 /16 (30) 1 (25) 90 (400) 110 (489) N/A N/A N/A N/A 1 3 /16 (30) N/A * Representative results of testing and a safety factor of 5. T = Tensile Strength S= Shear Strength Hilti Product Technical Guide 10/99 135

19 , Anchoring Systems, INSTALLATION INSTRUCTIONS Solid Base Materials, 1. Drill hole (depth = anchor length minus 2. Insert thickness fastened plus 1 /2"). anchor. Hollow Base Materials Impact Anchor Set the anchor with a hammer or set with an electric driver. Drive with a hammer or use an electric driver An accurately matched anchor length provides optimized holding power by allowing for expansion in the first part of the brick or block ORDERING INFORMATION Carbon Steel Description 3 /16 x /16 ( 5) 3/8 ( 9) 3/ /16 x 1 1 / /8 (15) 3/4 (19) 3/ /4 x /8 ( 3) 3/16 ( 5) 1/ /4 x 1 5 / /8 (15) 3/4 (19) 1/ /4 x 2 1 / (25) 1 3 /16 (30) 1/ /4 x 2 5 / /8 (4 1 3 /4 (44) 1/ /16 x 1 5 / /8 ( 9) 5/8 (15) 5/ /16 x 2 1 / /16 (30) 1 3 /8 (35) 5/ /16 x 3 5 / /8 (60) N/A 5/ /16 x 4 3 / /8 (85) N/A 5/16 50 Stainless Steel Item No. Fastenable Material Thickness in Concrete max in. Fastenable Material Thickness in Hollow Base Materials max in. Bit Diameter in. R 3 /16 x /16 ( 5) 3/8 ( 9) 3/ R 3 /16 x 1 1 / /8 (15) 3/4 (19) 3/ R 1 /4 x /8 ( 3) 3/16 ( 5) 1/4 200 R 1 /4 x 1 5 / /8 (15) 3/4 (19) 1/4 100 R 1 /4 x 2 1 / (25) 1 3 /16 (30) 1/4 100 R 1 /4 x 2 5 / /8 (4 1 3 /4 (44) 1/4 100 R 5 /16 x 3 5 / /8 (60) N/A 5/16 50 R 5 /16 x 4 3 / /8 (85) N/A 5/16 50 Box Quantity 136 Hilti Product Technical Guide 10/99

20 impact anchor Features: Material: Drive : - base material: concrete and solid or hollow brick - ready-to-use anchor for through-fastening - bridging of gaps due to collapsible section - impact expansion by hammer or driver - wide product programme - removable and adjustable with a driver - PA 6.6 polyamide, contains no heavy metals - contains no cadmium or lead - contains no halogens or silicones - in-place temperature range: from 40 C to +80 C - temperature when setting: from 10 C to +40 C - steel galvanised to 5 microns - stainless steel, A2 grade - copper Basic loading data (for a single anchor): All data on this page applies to concrete, f cc = N/mm 2 different kinds of bricks aerated concrete no edge distance and spacing influence Mean ultimate resistance, R u,m [kn]: Base material Anchor size 5/0-5/15 6/0 6/25 6/30-6/40 8/0-8/40 8/60 8/100 NRu,m Concrete, fcc= N/mm 2 VRu,m Solid brick, Mz NF Sand-lime solid block, KS DF Aerated concrete, PB 4 NRu,m VRu,m NRu,m VRu,m NRu,m VRu,m The ultimate loads were determined in holes drilled with drill bits of the minimum diameter. 131

21 impact anchor Design resistance, R d [kn]: Base material Anchor size 4/0 5/0 5/5-5/15 6/0-6/25 6/30-6/40 8/0 8/10-8/40 8/60-8/100 NRd Concrete, fcc= N/mm 2 VRd Engineering brick, 12 hole, class B Perforated brick, 3 hole cammon Themalite block, 7 N lightweight NRd VRd NRd VRd NRd VRd Themalite block, NRd ½ N lightweight VRd NRd Aerated concrete, PB 4, PB 6 VRd Extruded brick, Boral 10 NRd VRd Recommended load, L rec [kn]: Base material Anchor size 4/0 5/0 5/5-5/15 6/0-6/25 6/30-6/40 8/0 8/10-8/40 8/60-8/100 NRec Concrete, fcc= N/mm 2 VRec Engineering brick, 12 hole, class B Perforated brick, 3 hole cammon Themalite block,7 N, lightweight NRec VRec NRec VRec NRec VRec Themalite block, NRec ½ N lightweight VRec NRec Aerated concrete, PB 4, PB 6 VRec Extruded brick, Boral 10 NRec VRec Hole drilled with TE-CX drill bit, without hammering action. If at temperatures above 40 C loads are sustained, recommended loads should be reduced. Setting details l ~ 2mm d o d n h nom t fix h 1 132

22 impact anchor Features: Material: Drive : - base material: concrete and solid or hollow brick - ready-to-use anchor for through-fastening - bridging of gaps due to collapsible section - impact expansion by hammer or driver - wide product programme - removable and adjustable with a driver - PA 6.6 polyamide, contains no heavy metals - contains no cadmium or lead - contains no halogens or silicones - in-place temperature range: from 40 C to +80 C - temperature when setting: from 10 C to +40 C - steel galvanised to 5 microns - stainless steel, A2 grade - copper Basic loading data (for a single anchor): All data on this page applies to concrete, f cc = N/mm 2 different kinds of bricks aerated concrete no edge distance and spacing influence Mean ultimate resistance, R u,m [kn]: Base material Anchor size 5/0-5/15 6/0 6/25 6/30-6/40 8/0-8/40 8/60 8/100 NRu,m Concrete, fcc= N/mm 2 VRu,m Solid brick, Mz NF Sand-lime solid block, KS DF Aerated concrete, PB 4 NRu,m VRu,m NRu,m VRu,m NRu,m VRu,m The ultimate loads were determined in holes drilled with drill bits of the minimum diameter. 131

23 impact anchor Design resistance, R d [kn]: Base material Anchor size 4/0 5/0 5/5-5/15 6/0-6/25 6/30-6/40 8/0 8/10-8/40 8/60-8/100 NRd Concrete, fcc= N/mm 2 VRd Engineering brick, 12 hole, class B Perforated brick, 3 hole cammon Themalite block, 7 N lightweight NRd VRd NRd VRd NRd VRd Themalite block, NRd ½ N lightweight VRd NRd Aerated concrete, PB 4, PB 6 VRd Extruded brick, Boral 10 NRd VRd Recommended load, L rec [kn]: Base material Anchor size 4/0 5/0 5/5-5/15 6/0-6/25 6/30-6/40 8/0 8/10-8/40 8/60-8/100 NRec Concrete, fcc= N/mm 2 VRec Engineering brick, 12 hole, class B Perforated brick, 3 hole cammon Themalite block,7 N, lightweight NRec VRec NRec VRec NRec VRec Themalite block, NRec ½ N lightweight VRec NRec Aerated concrete, PB 4, PB 6 VRec Extruded brick, Boral 10 NRec VRec Hole drilled with TE-CX drill bit, without hammering action. If at temperatures above 40 C loads are sustained, recommended loads should be reduced. Setting details l ~ 2mm d o d n h nom t fix h 1 132

24 impact anchor Setting details Anchor size 4/0 5/0 5/5 5/10 5/15 6/0 6/5 6/10 6/15 6/25 6/30 6/40 d0 [mm] Drill bit diameter h0 [mm] Hole depth hnom [mm] Anchorage depth tfix [mm] Fixture (fastenable) thickness l [mm] Anchor length dn [mm] Head diameter Drill bit TE-C-4/9.5 TE-CX-5/12 TE-CX-6/12 Setting details Anchor size 8/0 8/10 8/20 8/30 8/40 8/60 8/80 8/100 d0 [mm] Drill bit diameter h0 [mm] Hole depth hnom [mm] Anchorage depth tfix [mm] Fixture (fastenable) thickness l [mm] Anchor length dn [mm] Head diameter Drill bit TE-CX-8/17 Installation equipment Rotary hammer (TE1, TE 2; TE5, TE6, TE6A, TE15, TE15-C or TE18-M), a hammer, a Pozi cross-recess driver, size 2 or 1, or a driver with Pozi cross-recess bit, size 2 or 1. Setting operations Drill hole with drill bit Install anchor. Hammer in anchor. Drill hole with drill bit. Install anchor. Drive in anchor. 133

25 Anchoring Systems HSP/HFP Drywall Anchor PRODUCT DESCRIPTION The Hilti HSP/HFP Drywall Anchor is a self-drilling anchor designed for fast and reliable fastenings in drywall. Product Features Shark tooth design for correct positioning and quick installation Cuts its own thread - no predrilling necessary One Hilti bit for anchor and setting Can be set with electric or standard driver for quick and simple installation Removability adds to the anchor s versatility Available in non-conductive nylon or zinc for a variety of applications Available with and without s for your convenience MATERIAL SPECIFICATIONS Zinc Nylon TECHNICAL DATA HSP/HFP Drywall Anchor Allowable Loads 1 Gypsum Wall Board 1/2" 5/8" HSP with Screw Tension Shear Tension Shear # 8 x 1 3/16 lb (N) lb (N) lb (N) lb (N) HFP with Screw # 8 x 1 (70) (180) (100) (270) 1. Based on using a safety factor of INSTALLATION INSTRUCTIONS Push the teeth of the anchor into the drywall panel. Drive the anchor (clockwise rotation) until it lies flush with the wall. Drive and tighten the with the Hilti bit ORDERING INFORMATION HDS Drywall Anchor Program Item no. Description Anchor lenght l d (in.) Screw dia. (in.) Quantity Remarks HSP 1 1/2 # HSP-S 1 1/2 # Delivered with 100 s, # 8 x 1 3/ HSP-1/4 THREAD 1 1/2 100 Delivered with one bit D-B SQ HSP-G ( ) HFP 1 1/8 # HFP-S 1 1/8 # Delivered with 100 s, # 8 x D-B PH2 HSP/HFP D-B SQ HSP-G 5 Hilti Product Technical Guide 10/99 139

26 HUD-1 universal anchor Features: Material: - base material: concrete, solid brick, hollow brick, gas (aerated) concrete, gypsum panel - high holding power - suitable for through-fastening with - resistance to turning in hole and premature expansion - low driving torque permits rapid setting - resistant to temperature, impact and chemicals - optimal guidance - PA 6 polyamide, contains no heavy metals - contains no cadmium or lead - contains no halogens or silicones - in-place temperature range: from 40 C to +80 C - temperature when setting: from 10 C to +40 C HUD-1 Basic loading data (for a single anchor): HUD-1 All data on this page applies to concrete, f cc = 30 N/mm 2 different kinds of base material no edge distance and spacing influence Characteristic resistance, R k [kn]: Anchor size HUD-1 HUD-1 HUD-1 HUD-1 HUD-1 HUD-1 Base material 5x25 6x30 8x40 10x50 12x60 14x70 Particle Particle Particle Particle Wood- Wood- Wood- Wood- Woodscre Wood- board board board board Non-cracked concrete, NRk fcc = 30 N/mm 2 VRk NRk Aerated concrete PB 2 VRk NRk Aerated concrete, PB 4 VRk Solid brick, Mz NF NRk ) VRk Sand lime solid block, NRk ) KS DF VRk NRk Hollow brick, HlzB x 5DF VRk Hollow brick, HlzB x 5DF NRk mm plastered, DIN VRk Gypsum panel 2), 12.5 mm Gypsum panel 2) 2x12.5 mm NRk ) - - VRk NRk ) 1.0 3) 1.5 4) - VRk Fibre reinforced gypsum panel NRk mm VRk Fibre reinforced gypsum panel NRk x12.5 mm VRk Issue 2005

27 HUD-1 universal anchor Design resistance, R d [kn]: Anchor size HUD-1 HUD-1 HUD-1 HUD-1 HUD-1 HUD-1 Base material 5x25 6x30 8x40 10x50 12x60 14x70 Particle Particle Particle Particle Wood- Wood- Wood- Wood- Woodscre Wood- board board board board Non-cracked concrete, NRd fcc = 30 N/mm 2 VRd NRd Aerated concrete, PB 2 VRd Aerated concrete, PB4 Solid brick, Mz NF NRd VRd NRd ) VRd Sand lime solid block, NRd ) KS DF VRd NRd Hollow brick, HlzB x 5DF VRd Hollow brick, HlzB x 5DF NRd mm plastered, DIN VRd Gypsum panel 2), 12.5 mm Gypsum panel 2), 2 x12.5 mm Recommended Load, L rec [kn]: Anchor size HUD-1 HUD-1 HUD-1 HUD-1 HUD-1 HUD-1 Base material 5x25 6x30 8x40 10x50 12x60 14x70 Particle Particle Particle Particle Wood- Wood- Wood- Wood- Wood- Woodboard board board board Non-cracked concrete, NRec fcc = 30 N/mm 2 VRec NRec Aerated concrete, PB 2 VRec NRec Aerated concrete, PB 4 VRec Solid brick, Mz NF NRec ) VRec Sand lime solid block, NRec ) KS DF VRec NRec Hollow brick, HlzB x 5DF VRec Hollow brick, HlzB x 5DF NRec mm plastered DIN VRec Gypsum panel 2), 12.5 mm Gypsum panel 2), 2 x12.5 mm NRd ) - - VRd NRd ) ) ) - VRd Fibre reinforced gypsum panel NRd mm VRd Fibre reinforced gypsum panel NRd x12.5 mm VRd NRec ) - - VRec NRec ) 0.2 3) 0.3 4) - VRec Fibre reinforced gypsum panel NRec mm VRec Fibre reinforced gypsum panel NRec x12.5 mm VRec Issue